For any test page or network page press (ctrl +F )key from the key board and type the model no or first two digit of the model no series. these all the information has been taken from hp.com , you can find these information very easily at hp.com.
HP Deskjet 5100, 5440, 5500, 5740, and 5940 Series Printers - Printing Internal Tests (c00213132)
Introduction
This document explains how to perform built-in internal tests on specific HP Deskjet printers.
The internal tests can be used to verify that the printer's internal firmware is functioning properly. The tests do not verify that the computer and printer connections are working properly.
Running a sample page
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a self-test
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
Continuous "H" test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button eight times.
4. Release the POWER button.
NOTE: To cancel the "Continuous H" test page, press the CANCEL button once.
Page count test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button twelve times.
4. Release the POWER button.
Two-sided printing module (duplexer) test
1. Press and hold down the POWER button.
2. Press the CANCEL (X ) button three times.
3. Press the RESUME button once.
4. Release the POWER button.
Media sense test
The following test will identify the type of media in the IN tray. Pages will continuously print until the CANCEL button is pressed.
1. Press and hold down the POWER button.
2. Press the CANCEL (X) button ten times.
3. Release the POWER button.
4. Press CANCEL after printing one or two pages.
Pages will print with the name of the printer, the serial number of the printer, and a code indicating the type of media being used. The third line says MS Result and will be followed by one of the codes listed below:
· PLNA = plain paper
· PHTC = photo paper
· TRNA = transparency
· PRMA = premium paper
Skew measurement test
1. Press and hold down the POWER button.
2. Press the CANCEL (X) button three times.
3. Press the RESUME button two times.
4. Release the POWER button.
HP Deskjet 400 series printers
HP Deskjet 400, 400L, and 420c series printers
Running a self-test
1. Turn the printer off.
2. Press and hold down the PAPER FEED button.
3. Turn the printer on.
4. Release the PAPER FEED button.
Running a clean test
1. Turn the printer on.
2. Press and hold down the CHANGE CARTRIDGE button for five seconds.
HP Deskjet 500 series printers
HP Deskjet 500, 500c, 520, 550c, and 560c series printers
Running a self-test
Press FONT and RESET, or LOAD EJECT while turning on the printer.
Running a clean test
1. Turn the printer on.
2. Press the CLEAN button.
Running an alignment test
1. Turn the printer on.
2. Press the ALIGNMENT TEST button.
HP Deskjet 540 printers
Running a self-test
1. Turn the printer on.
2. Press and hold down the RESUME button until the printer starts printing.
Running a clean test
1. Turn the printer on.
2. Press and hold down the POWER button.
3. Press the RESUME button seven times.
4. Release the POWER button.
Running a diagnostic test
Regular
1. Turn the printer on.
2. Press and hold down the POWER button.
3. Press the RESUME button five times.
4. Release the POWER button.
Extended
1. Turn the printer on.
2. Press and hold down the POWER button.
3. Press the RESUME button twelve times.
4. Release the POWER button.
Running a continuous test
1. Turn the printer on.
2. Press and hold down the POWER button.
3. Press the RESUME button ten times.
4. Release the POWER button.
HP Deskjet 600 series printers
HP Deskjet 600, 600c, 610c, 630c, 632c, 640c, 642c, 648c, 660c, 670c, 680c, and 690c series printers
Running a self-test
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a clean-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button seven times.
4. Release the POWER button.
Running a diagnostic-test
Regular
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button five times.
4. Release the POWER button.
Extended
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button twelve times.
4. Release the POWER button.
HP Deskjet 656c printer
Running a diagnostic-test
Regular
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button five times.
4. Release the POWER button.
Extended
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button twelve times.
4. Release the POWER button.
HP Deskjet 700 series printers
HP Deskjet 710c and 720c series printers
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
This may need to be performed several times before the printer prints the page.
NOTE: There are no internal clean or diagnostic tests for the HP Deskjet 710c and 720c series printers. The clean test can be performed from the printer’s toolbox.
HP Deskjet 800 series printers
HP Deskjet 820c printers
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
NOTE: There are no internal clean or diagnostic tests for the HP Deskjet 820cse and 820cxi printers.
HP Deskjet 810c, 825c, 830c, 840c, 845c, 880c, and 895c series printers
Running a sample page
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a diagnostic test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
NOTE: There is no internal clean test for the HP Deskjet 810c, 830c, 880c, and 895c series printers.
HP Deskjet 850c, and 870c, and 890c series printers
Running a self-test
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a clean-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button seven times.
4. Release the POWER button.
Running a diagnostic test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button five times.
4. Release the POWER button.
HP Deskjet 900c series printers
HP Deskjet 916c, 920c, 930c, 940c, 950c, 970c, 960c, 980c, and 990c series printers
Running a sample page
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
Running a diagnostic test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the X (Cancel Print ) button eight times.
4. Press the RESUME button four times.
5. Release the POWER button.
Two-sided printing module (duplexer) test
1. Press and hold down the POWER button.
2. Press the CANCEL (X ) button three times.
3. Press the RESUME button once.
4. Release the POWER button.
HP Deskjet 3000 series printers
HP Deskjet 3000 series printers (except for HP Deskjet 3820 series)
Running a diagnostic test
1. Turn the printer on.
2. Press and hold down the POWER button.
3. Open and close the top cover four times.
4. Release the POWER button.
NOTE: When running the test on an HP Deskjet 3600 series printer it may be helpful to use a pen or pencil to hold down the Power button.
HP Deskjet 3820 printers
Running a sample page
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
HP Deskjet 5000 series printers
HP Deskjet 5000 series printers
Printing a Network Configuration page (DJ 5850 printers only)
If the printer has just been connected to a network, wait a few minutes before printing the Network Configuration page to allow the printer to obtain valid settings.
1. Ensure the printer is on and is idle.
2. Press the NETWORK PAGE button once.
Running a sample page
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
Continuous "H" test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button eight times.
4. Release the POWER button.
NOTE: To cancel the "Continuous H" test page, press the CANCEL button once.
Page count test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button twelve times.
4. Release the POWER button.
Two-sided printing module (duplexer) test
1. Press and hold down the POWER button.
2. Press the CANCEL (X ) button three times.
3. Press the RESUME button once.
4. Release the POWER button.
Media sense test
The following test will identify the type of media in the IN tray. Pages will continuously print until the CANCEL button is pressed.
1. Press and hold down the POWER button.
2. Press the CANCEL (X) button ten times.
3. Release the POWER button.
4. Press CANCEL after printing one or two pages.
Pages will print with the name of the printer, the serial number of the printer, and a code indicating the type of media being used. The third line says MS Result and will be followed by one of the codes listed below:
o PLNA = plain paper
o PHTC = photo paper
o TRNA = transparency
o PRMA = premium paper
Skew measurement test
1. Press and hold down the POWER button.
2. Press the CANCEL (X) button three times.
3. Press the RESUME button two times.
4. Release the POWER button.
HP Deskjet 5100 printers
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
HP Deskjet 6000 series printers
Running a sample page
NOTE: This test does not work with the HP Deskjet 6830v and 6840 series printers.
1. Turn the printer on.
2. Press and hold the RESUME button until the printer starts printing.
3. Release the RESUME button.
Running a self-test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button four times.
4. Release the POWER button.
Continuous "H" test
1. Turn the printer on.
2. Press and hold the POWER button.
3. Press the RESUME button eight times.
4. Release the POWER button.
NOTE: To cancel the "Continuous H" test page, press the CANCEL button once.
Two-sided printing module (duplexer) test
1. Press and hold down the POWER button.
2. Press the CANCEL (X ) button three times.
3. Press the RESUME button once.
4. Release the POWER button.
HP Deskjet 6830v, 6940, and 6980 series printers
Customer Support Diagnostic test page
1. Press and hold the Power button.
2. While holding the Power button, press the Cancel (X) button, and then release both buttons.
3. Resetting the printer press and hold down the check mark button and press cancel button three times
HP Deskjet D1300, D1400, D2300, and D2400 series printers
Running a self-test
1. Turn the printer on.
2. Press and hold down the Power button.
3. While holding down the Power button, open and shut the lid of the printer four times.
4. Release the Power button. The self-test prints.
NOTE: When running the test on an HP Deskjet D2300 series printer it may be helpful to use a pen or pencil to hold down the Power button.
HP Deskjet D4100 and D4200 series printers
Customer Support Diagnostic Test Page
1. Hold down the Power button.
2. While holding down the Power button, press the Photo button once. The test page prints.
Continuous "H" test
1. Hold down the Power button.
2. While holding down the Power button, press the Photo button once and the Resume button three times. The Continuous "H" test prints.
HP Deskjet, Officejet, and Photosmart All-in-Ones and Deskjet and Photosmart Printers - Printing and Reading a 10-tap Test (c00110093)
Introduction
This document explains how to print a 10-tap test from the control panel of the product for HP All-in-One, Deskjet, Officejet Pro, and Photosmart products. Use the 10-tap test to troubleshoot print quality, mechanical problems, or other issues.
NOTE: This document applies only to regionalized products.
Printing and reading a 10-tap test
The following sections contain steps for printing a 10-tap test on HP All-in-Ones and printers.
NOTE: Some products do not include 10-tap tests. In these cases, this document contains instructions for printing a self-test.
HP Deskjet Printers
1. Press and hold the Power button, and then press the Cancel button once.
2. Release the buttons. The 10-tap test prints.
HP Deskjet 460 and Officejet H470 Mobile Printer series
1. Make sure the product is on and loaded with unused, plain white paper.
2. Hold down the Power button ( ), and then press the Resume button ( ) 10 times. Release both buttons, and the test page prints.
Figure 1: Power and Resume buttons
1 - Power button
2 - Resume button
HP Deskjet 3900 Printer series
1. Press and hold the power button ( ).
Figure 2: Power button
2. Raise and lower the product cover four times.
3. Release the power button ( ), and the self-test page prints.
HP Deskjet 5740 Printer series
1. Turn the product on.
2. Press and hold the Power button ( ).
3. Press the Cancel button ( ).
4. Release both buttons. The 10-tap test prints.
HP Deskjet 6940 Printer series
1. Turn the product on.
2. Press and hold the Power button ( ).
3. Press the Cancel button ( ).
4. Release both buttons. The 10-tap test prints.
HP Deskjet D1400 Printer series
1. Turn the product on.
2. Press and hold the Power button ( ).
3. While holding down the Power button ( ), open and shut the lid of the product four times.
4. Release the Power button ( ). The self-test prints.
Figure 5: HP Deskjet D1400 Printer series self-test page
HP Deskjet D2400 Printer series
1. Turn the product on.
2. Use a pencil to press and hold down the Power button ( ).
3. While holding down the Power button ( ), open and shut the lid of the product four times. You only have to raise the lid until it touches the pencil.
4. Release the Power button ( ). The self-test prints.
Figure 6: HP Deskjet D2400 Printer series self-test page
HP Deskjet D4200 Printer series
1. Make sure plain white paper is loaded in the product.
2. Press and hold the Power button ( ).
3. Press the Photosmart Essential button, and then release both buttons.
4. The self-test prints.
Figure 7: HP Deskjet D4200 Printer series self-test page
1. .
1. .
HP Photosmart Printers
Photosmart 320, 330, 370, and 380 Printer series
1. Press either the Right Arrow button ( ) or the Left Arrow button ( ). Main Menu displays on the control panel.
2. Press OK to select Tools .
3. Press the Right Arrow button ( ) to select Print Test Page , and then press OK . The test page prints.
Photosmart 420 Printer series
1. Make sure the camera is in the camera dock.
2. Load paper in the input tray. Use plain paper or index cards to conserve photo paper.
3. Press Menu/OK ( ) on the control panel to select Print Menu .
4. Press the Down Arrow button ( ) to select Print Test Page , and then press OK . The test page prints.
Photosmart 470 Printer series
1. Press Menu . Main Menu displays on the control panel.
2. Press the Down Arrow button ( ) to select Tools , and then press OK .
3. Press the Down Arrow button ( ) to select Print Test Page , and then press OK . The test page prints.
Photosmart 7800 Printer series
1. Press and hold the OK button, and then press the Left Arrow button ( ) once.
2. Release the buttons. The 10-tap test prints.
Photosmart 7800 Printer series - Self-test
1. Open the printer Toolbox using one of the following two options:
§ Click Start , click HP , and then click HP Solution Center . In HP Solution Center, click Print Settings , and then click Printer Toolbox .
§ Or in your printing application, select File , Print , and click Properties . Click the Services tab, and then click Service This Device .
2. Click Print a Diagnostic Page , and then click Print Page . The test page prints.
Photosmart 8000 Printer series
1. Press the Menu button, press the Right Arrow button ( ) to select Tools , and then press OK .
2. Press the Right Arrow button ( ) several times to select Print test page , and then press OK . The test page prints.
Photosmart 8100 and 8400 Printer series
1. Make sure the main tray is loaded with full size media, and that the tray selector is in the main tray position (the lever is all the way out).
2. Press and hold Cancel and Save . Hold both buttons for about five seconds.
3. The Service menu displays on the control panel. Scroll to Customer Diagnostic Test and press OK . The 10-tap test prints.
Photosmart 8200 Printer series
1. Make sure the main tray is loaded with clean, plain white paper.
2. Press Menu , and then press the Down Arrow button ( ) to scroll down to Tools . Press OK .
3. Press the Down Arrow button ( ) to scroll to Print Test Page , and then press OK . The report prints.
Photosmart 8750 Professional Photo Printer
1. Make sure the product is on and the main tray is loaded with unused, plain white paper. Adjust the paper guides, as needed, against the stack of paper.
2. Press and hold Layout and the Right Arrow button ( ) for several seconds until Tap Test #0 displays on the control panel.
Figure 8: Diagnostic page buttons
1 - Layout
2 - Right Arrow
3. Press the Layout button once. Tap Test #10 displays on the control panel.
- Press OK . The 10-tap test prints.
Photosmart A430 Portable Photo Printer
1. Press the Menu button to select Main Menu .
2. Press the Down Arrow button ( ) until Tools displays on the control panel, and then press OK .
3. Press the Down Arrow button ( ) until Print Test Page displays on the control panel, and then press OK . The test page prints.
Photosmart A432, A433, A434, and A436 Portable Photo Printers
1. If the product is not already on, press the Power button ( ) to turn it on.
2. Press Menu/OK ( ). The Print menu displays on the control panel.
3. Press the Down Arrow button ( ) below Menu/OK ( ) to select Tools .
4. Press Menu/OK ( ).
5. Press the Down Arrow button ( ) to select Print Test Page .
6. Press Menu/OK ( ). Load paper, then press OK displays on the control panel.
7. If paper is not already loaded in the product, and then load a few sheets of clean, unused, plain white paper into the product.
8. Press Menu/OK ( ). The self-test page prints.
Figure 9: HP Photosmart A432, A433, A434, and A436 Portable Photo Printers self-test page
HP Photosmart A440 Photo Printer series
1. Press Menu/OK ( ) on the control panel, press the Down Arrow to select Print , and then press ( ).
2. Press the 4–way arrow button to select Tools , and then press ( ).
3. Press the Down Arrow button ( ) or the Up Arrow button ( ) to select Print test page , and then press ( ). The self-test page prints.
Figure 10: HP Photosmart A440 Photo Printer series self-test page
HP Photosmart A510, A512, and A516 Compact Photo Printers
1. Press the Left Arrow button ( ) or the Right Arrow button ( ) to open the printer menu.
2. Press Menu/OK ( ) to open the print menu.
3. Select Tools , and then press OK .
4. Select Print test page , and then press OK . The self-test page prints.
Figure 11: HP Photosmart A510, A512, and A516 Compact Photo Printers self-test page
HP Photosmart A610, A612, A616, A617, and A618 Compact Photo Printers
1. Press OK on the printer to open the print menu.
2. Press the 4–way arrow button to select Tools , and then press OK .
3. Press the Left Arrow button ( ) or the Right Arrow button ( ) to select Print test page , and then press OK . The self-test page prints.
Figure 12: HP Photosmart A610, A612, A616, A617, and A618 Compact Photo Printers self-test page
Photosmart D7100 Printer series
1. Press and hold OK .
2. Press Cancel .
3. Release the OK button. The test page prints.
HP Officejet H470, H470b, H470wf, and H470wbt Printers - Printing a Network Configuration Page (c01445960)
Print a network configuration page from the product control panel
o Hold the Power button ( ), and then press the Cancel button ( ) 24 times.
The network configuration page prints.
HP Deskjet 6127 - Printing and Using a Network Configuration Page (bpd09620)
While the printer is powered on and idle, press the CANCEL button (X) on the printer to print a Network Configuration page (see Figure 1).
HP Deskjet Printers and HP Officejet Pro 8500 Premier (A909n) and 8500 Wireless (A909g) All-in-One Printers - The Printer Loses the Network Connection When Using Wireless Channels 12 and 13 (c00383332)
Issue
When you try to set up the product on a wireless network using wireless channels 12 and/or 13, the product loses the network connection. The network lights on the product are not lit and, after you turn the product off and then back on, the printer scans the network and then the network lights go out.
The Network configuration page and the Report page show that the wireless status is “disassociated”, and the IP address is 0.0.0.0.
This document applies to the following products:
· HP Deskjet 6840, 6840dt, 6840xi, 6843, 6848 Printers
· HP Deskjet 6940, 6943, 6980, 6983 Printers
· HP Officejet Pro 8500 Premier (A909n) All-in-One Printer
· HP Officejet Pro 8500 Wireless (A909g) All-in-One Printer
Solution
The product cannot connect to a network using channels 12 and 13. The product functions on channels 1 through 11.
HP Photosmart 100 and 130 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure 10 x 15 cm paper is loaded in the In Tray.
- On the control panel, press and hold the Print button until the printer begins to print a test page.
HP Photosmart 140 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure 10 x 15 cm paper is loaded in the paper In Tray.
- On the control panel, press the Left/Right Select Photo button to highlight Print Test Page .
- Press the OK button.
HP Photosmart 230 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure 10 x 15 cm paper is loaded in the In Tray.
- Press the Menu button.
- Scroll up (use the Up/Down arrow button) to highlight Print Test Page .
- Press the OK button.
HP Photosmart 245, 375, and 385 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure 10 x 15 cm paper is loaded in the In Tray.
- Press the Menu button.
- Press the Up/Down arrow button to display the Tools menu. Then press the OK button.
- Press the Up/Down arrow button to highlight Print Test Page .
- Press the OK button.
HP Photosmart 325 and 335 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure 10 x 15 cm paper is loaded in the paper In Tray.
- Press the Left/Right Select Photo button to highlight the Tools menu and then press the OK button.
- Press the Left/Right Select Photo button to highlight Print Test Page .
- Press the OK button.
HP Photosmart 420 series printers
- Place the camera onto the docking connector. If the printer does not turn on automatically, turn on the printer.
- Make sure 10 x 15 cm paper is loaded in the In Tray.
- Press the OK button to display the camera menus.
- Press the Up/Down arrow button to highlight Print Test Page .
- Press the OK button.
- When prompted to insert plain paper, press the OK button again.
HP Photosmart 470 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure 10 x 15 cm paper is loaded in the In Tray.
- Press the Menu button.
- Press the Up/Down arrow button to display the Tools menu. Then press the OK button.
- Press the Up/Down arrow button to highlight Print a Test Page .
- Press the OK button.
HP Photosmart 1000, 1100, and 1115 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure plain paper is loaded in the In Tray.
- On the control panel, press the Right arrow in the Tools button until Print a Test Page? is displayed.
- Press the OK/Yes button.
HP Photosmart 1215, 1218, and 7600 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure plain paper is loaded in the In Tray.
- On the control panel, press the Right arrow in the Menu button until Print a Test Page? is displayed.
- Press the OK/Yes button.
HP Photosmart 1315 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure plain paper is loaded in the In Tray.
- Press the Menu button.
- Press the Up/Down arrow button to highlight Print a Test Page . Then press the tick symbol button.
HP Photosmart 7150 series printers
- Make sure plain paper is loaded in the In Tray.
- Press and hold the Power button.
- Press the Resume button four times.
- Release the Power button.
HP Photosmart 7200 and 7400 series printers
- Make sure plain paper is loaded in the In Tray.
- Press and hold the Power button.
- Press the Save button four times.
- Release the Power button.
HP Photosmart 7350 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure plain paper is loaded in the In Tray.
- On the control panel, press the Right/Left arrow button in the Tools button several times until Print a Test Page? is displayed.
- Press the OK/Yes button.
HP Photosmart 7550, 7700, 7960, 8150 and 8450 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure plain paper is loaded in the In Tray.
- Press the Menu button.
- Press the Up/Down arrow button to display the Tools menu. Then press the OK button.
- Press the Down arrow button to highlight Print a Test Page . Then press the OK button.
HP Photosmart 7850 series printers
- Make sure plain paper is loaded in the In Tray.
- Press and hold the Select button.
- Press the Left arrow button once.
- Release the Select button.
HP Photosmart 8050 and 8250 series printers
- Ensure that the memory card has been removed from the memory card slot.
- Make sure plain paper is loaded in the In Tray.
- Press the Menu button.
- Press the Up/Down arrow button to display the Tools menu. Then press the OK button.
- Press the Up/Down arrow button to highlight Print a Test Page .
- Press the OK button.
HP Photosmart 8750 professional series printers
- Make sure plain paper is loaded in the In Tray.
- Press the Menu button on the printer control panel.
- Press the Right arrow button six times.
- Confirm the display says Print a test page .
- Press the Select Photo button on the control panel to print the test page.
HP Photosmart A300 series
- Make sure the printer is turned on.
- Load paper in the input tray. Use plain paper or index cards to conserve photo paper.
- Press and hold down the OK button.
- Press the On button two times to print a test page.
HP Photosmart A400 series
|
|
NOTE:
|
The camera must be in the camera dock on the printer in order to print a self test.
|
- Make sure the printer is turned on.
- Dock the camera on the printer. (Turn on the camera manually if it does not turn on automatically. The Camera LCD acts as the LCD for the Printer when docked.)
- Load paper in the input tray. Use plain paper or index cards to conserve photo paper.
- Press the Menu/OK button on the printer.
- Press the Left/Right arrow button to highlight Settings .
- Press the Up/Down arrow button to highlight Tools .
- Press the Menu/OK button on the printer.
- Press the Up/Down arrow button to highlight Print Test Page .
- Press the Menu/OK button on the printer to begin printing the test page.
HP Photosmart A500 series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Load paper in the input tray. Use plain paper or index cards to conserve photo paper.
- Press the Left/Right arrow button to open the printer menu.
- Press the Left/Right arrow button to highlight Tools . Press the OK button.
- Press the Left/Right arrow button to highlight Print Test Page . Press the OK button.
HP Photosmart A600 series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Load paper in the input tray. Use plain paper or index cards to conserve photo paper.
- Press the Menu button to open the printer menu.
- Press the Up/Down arrow button to highlight Tools . Press the OK button.
- Press the Up/Down arrow button to highlight Print Test Page .
- Press the OK button to begin printing the test page.
HP Photosmart A700 Series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Load paper in the input tray. Use plain paper or index cards to conserve photo paper.
- Press the Menu button to open the printer menu.
- Press the Up/Down arrow button to highlight Tools. Press the OK button.
- Press the Up/Down arrow button to highlight Print Test Page .
- Press the OK button to begin printing the test page.
HP Photosmart D5000 Series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Make sure plain paper is loaded in the In Main Tray.
- Press and hold the OK button.
- Press and release the Left arrow button once. The printer display shows 10 briefly.
- Release the OK button to print the Test Page.
HP Photosmart D5100 Series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Make sure the CD tray is closed.
- Make sure plain paper is loaded in the In Main Tray.
- Press and hold the OK button.
- Press and release the Left arrow button once. The printer display shows 10 briefly.
- Release the OK button to print the Test Page.
HP Photosmart D7100 Series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Make sure plain paper is loaded in the In Tray.
- Press the Home button to access the Home screen.
- Press the Left/Right arrow button to highlight Settings . Then press the OK button.
- Press the Up/Down arrow button to display the Tools menu. Then press the OK button.
- Press the Up/Down arrow button to highlight Print Test Page .
- Press the OK button to begin printing the test page.
HP Photosmart D7300 Series
- Ensure that the memory card has been removed from the memory card slot.
- Make sure the printer is turned on.
- Make sure plain paper is loaded in the In Tray.
- Touch the home icon in the upper left-hand corner to access the home screen.
- Touch Settings on the screen.
- Touch Tools on the screen.
- Touch the Up/Down arrow on the right of the screen to scroll for more options.
- Touch Print Test Page to begin printing the test page
HP Color LaserJet 3700
Press the Checkmark (Select) to enter the MENUS. Press the Down Arrow to highlight INFORMATION . Press the Checkmark (Select) to select INFORMATION . Press the Down Arrow to highlight PRINT CONFIGURATION . Press Checkmark (Select) to select PRINT CONFIGURATION
HP Color LaserJet 2500 series
Press the green GO button and the small JOB CANCEL button simultaneously.
HP Color LaserJet 8550 and 8500 series
Press the MENU button until Information Menu appears on the display. Press the ITEM button until Print Configuration or Print EIO Page appears in the display. Press SELECT
HP Color LaserJet 4600
Press the Checkmark (Select) to enter the MENUS . Press the Down Arrow to highlight INFORMATION . Press the Checkmark (Select) to select INFORMATION . Press the Down Arrow to highlight PRINT CONFIGURATION . Press Checkmark (Select) to select PRINT CONFIGURATION
HP Color LaserJet 4500
Press the MENU button until Information Menu appears on the display. Press the ITEM button until "Print Configuration" appears in the display. Press the SELECT button.
HP Color LaserJet 5 series
Take the printer OFFLINE. Press the MENU button until Test Menu or PCL Test Menu appears in the display. Press the ITEM button until Self Test or PCL Configuration Page appears. Press SELECT or ENTER .
HP Color LaserJet
Select the ONLINE key to take the printer offline (the On Line indicator goes out). Press the MENU key until PCL Test Menu or PS Test Menu appears on the first line of the Printer's display panel. Note: the prefix PCL or PS depends on whether HP-PCL or PostScript has been selected as the current "system personality." For example, if you want to print a PS self test but the printer is currently set to PCL, you need to change the printer's personality to PostScript. To do this press the MENU key until PCL CONFIG MENU shows on the first line of the display panel. SYS=PCL or AUTO will appear on the second line. At this point, press the Plus (+) key once to change to PS and then press ENTER . Finally, press the ON LINE key and the printer will reset to the PS personality. PCL SELF TEST or PS SELF TEST should automatically appear on the second line. Press the ENTER key to print the self-test page. Press the ONLINE key to put the printer back online (the On Line indicator goes on).
HP LaserJet 9000
Press 2, 2 (press the 2 key twice) on the numeric keypad of the printer.
HP LaserJet 8100 and 8000 series
Press the MENU button until Information Menu appears on the display. Press the ITEM button until Print Configuration or Print EIO Page appears in the display. Press SELECT .
HP LaserJet 4200, 4250, 4300, 4350 series
Press the Checkmark (Select) to enter the MENUS . Press the Down Arrow to highlight INFORMATION . Press the Checkmark (Select) to select INFORMATION . Press the Down Arrow to highlight PRINT CONFIGURATION . Press Checkmark (Select) to select PRINT CONFIGURATION
HP LaserJet 5000, 4050, and 4000
Press the MENU button until Information Menu appears on the display. Press the ITEM button until "Print Configuration" appears in the display. Press the SELECT button.
HP LaserJet 2300
Press the Checkmark (Select) to enter the MENUS . Press the Down Arrow to highlight INFORMATION . Press the Checkmark (Select) to select INFORMATION . Press the Down Arrow to highlight PRINT CONFIGURATION . Press Checkmark (Select) to select PRINT CONFIGURATION .
HP LaserJet 2200, 2200dn, and 2200dtn
Press the GO and JOB CANCEL buttons simultaneously.
HP LaserJet 2100, 2100n, and 2100tn
Press the GO and JOB CANCEL buttons simultaneously.
HP LaserJet 5Si, and 5 series
Take the printer OFFLINE. Press the MENU button until Test Menu or PCL Test Menu appears in the display. Press the ITEM button until "Self Test" or "PCL Configuration Page" appears. Press SELECT or ENTER.
HP LaserJet 4 series, and the 4Si, 4V, 4Plus series
Take the Printer OFFLINE. Press the MENU button until Test Menu appears in the display. Press the ITEM button until Self Test appears in the display. Press ENTER
HP LaserJet IIIsi
Take the printer OFFLINE. Press the TEST button until 05 Self-Test appears in the display.
HP LaserJet III, and II series
Press and hold the STATUS button on the back of the HP Jetdirect XIO card. Continue holding the STATUS button until the printer starts printing. Note: This will be easier if the eraser end of a pencil is used to hold the button in.
For D1420,D1540 , D1400,D1500 series
Press and hold the Power button and open & close the top cover of the printer 4(four) times
For office jet Pro k 5400 ,
press the network button
Desk jet 6940 ,6980 , 6988
Press & hold down the ( )check mark button for three seconds.
deskjet 460 and officejet 470
press the ( ) cancel button once
Laserjet 1505
open and close the top cover 5 times when the printer powered on.
Prok 8600
Press cancel button for 3 seconds
